Perun

Perun for Krytac Kriss Vector replaces stock electronics in Kriss Vector airsoft replicas made by Krytac company. It provides lots of additional features, including active braking and full cycle control (making sure that each cycle is finished, even if the trigger is pulled very briefly).

Feature description

Freely programmable firing modes – Set any firing mode you like on any of the selector positions independently. Available modes are: safe, semi, binary, 2 to 5 round burst and auto.
Active brake - active brake stops the motor after each shot preventing spring compression or in case of replicas with high rate of fire, overspin (double shot problem).
Precocking - Fast trigger response can be a matter of victory or defeat, especially in CQB situations. With precocking enabled, piston will remain in rear position after each shot with the spring already compressed, ensuring that next shot will be fired immediately after you pull the trigger. To release the spring after using precocking, pull and hold the trigger. A second shot will be fired after 3 seconds, with no precocking and fully braked.
Rate of fire reduction - Reduce the rate of fire in automatic or burst fire to save ammo or make the replica shoot in a more realistic fashion.
Low battery voltage alarm - Dedicated for Li-Po and Li-Ion batteries. Should the battery voltage fall to a dangerously low level, user will be notified by short sound signals that are repeated every minute. This may also be freely switched on and off.
Diagnostic system - Constantly monitors the replica and the mosfet itself. In case of any problems, immediately lets you know what it might be, making troubleshooting much easier.
Electronic fuse - Will save your replica and battery in case of a major malfunction. It will automatically disconnect the battery if a short circuit or blocked motor is detected.

Programming of all the settings is done solely by using trigger and selector, in an easily memorable and quick sequence. Programming is supported by sound signals and multicolor LED diode. That allows changing the settings in any moment, in a matter of seconds, even under enemy fire.
Perun for Krytac Kriss Vector works without problems with any battery from 7V do 17V. It can also be used with most extreme setups, without any limitations as to the spring rating.

Manual download here 

AB++ AB++ is an on-wire mosfet, channelling the power from the battery to the motor through a specialized high-power transistor, instead of delicate mechanical switches, increasing reliability and replica performance. It also enhances your replica by adding many new, useful features. Comes with universal wiring, that can be used in any replica. Only few easy soldering joints are needed to install the mosfet.    

Feature description Electronic burst – Change auto to an electronically controlled burst to save your ammo and increase realism! Active brake - active brake stops the motor after each shot preventing spring compression or in case of replicas with a high rate of fire, overspin (double shot problem). Precocking - Fast trigger response can be a matter of victory or defeat, especially in CQB situations. With precocking enabled, the piston will remain in the rear position after each shot with the spring already compressed, ensuring that the next shot will be fired immediately after you pull the trigger. To release the spring after using precocking, pull the trigger while simultaneously holding the button on the unit. A shot will be fired, with no precocking and fully braked. Rate of fire reduction - Reduce the rate of fire in automatic or burst fire to save ammo or make the replica shoot in a more realistic fashion. DMR mode - Introduces intervals between semiautomatic shots to comply with DMR rules on some fields. Low battery voltage alarm - Dedicated for Li-Po and Li-Ion batteries. When the battery voltage fall to a dangerously low level, the user will be notified by short sound signals that are repeated every minute. This may also be freely switched on and off. Diagnostic system - Constantly monitors the replica and the mosfet itself. In case of any problems, immediately lets you know what it might be, making troubleshooting much easier. Electronic fuse - Will save your replica and battery in case of a major malfunction. It will automatically disconnect the battery if a short circuit or blocked motor is detected.   Programming of all the settings is done solely by using a trigger and a button on the device, in an easily memorable and quick sequences. Programming is supported by sound signals and a multicolor LED diode. That allows changing the settings at any moment, in a matter of seconds, even under enemy fire. Upgrade kit works without problems with any battery from 7V to 17V. It can also be used with most extreme setups, without any limitations as to the spring rating.

AUG Perun for AUG mechanical contacts in your AUG replica and provides lots of useful features. Magnetic sensors coupled with a magnet installed directly on the trigger, allow to remove the bar that connects trigger with the gearbox, making trigger pull much smoother. Optical detection of the sector gear position ensures a reliable single-fire function. Only replicas in Tokyo Marui standard are compatible with this mosfet, among which are those manufactured by: Tokyo Marui, Classic Army, JG, ASG.    

Feature description Adjustable trigger sensitivity – The trigger can be set to 5 sensitivity levels for both first and second trigger stage, ranging from short pull needed to fire a shot, to a long one. No modification to the trigger or the gearbox is needed and the trigger sensitivity change is possible even in the field. Selectable firing modes – User can choose firing modes available after short or long pull of the trigger: SEMI ONLY, BINARY, SEMI-AUTO, SEMI-BURST, BURST-AUTO. Active brake - active brake stops the motor after each shot preventing spring compression or in case of replicas with high rate of fire, overspin (double shot problem). Precocking - Fast trigger response can be a matter of victory or defeat, especially in CQB situations. With precocking enabled, piston will remain in rear position after each shot with the spring already compressed, ensuring that next shot will be fired immediately after you pull the trigger. To release the spring after using precocking, pull the trigger and hold it for 2 seconds, after which a second shot will be fired, this time with no precocking and fully braked. Binary trigger - Allows for easy double shots in semi-automatic setting. After enabling this mode, if semi-automatic fire is set, shots will be fired not only when the trigger is pulled, but also when it is released. Rate of fire reduction - Reduce the rate of fire in automatic or burst fire to save ammo or make the replica shoot in a more realistic fashion. Low battery voltage alarm - Dedicated for Li-Po and Li-Ion batteries. Should the battery voltage fall to a dangerously low level, user will be notified by short sound signals that are repeated every minute. This may also be freely switched on and off. DSG – a sector gear detection mode specially prepared to work with dual sector gears. Diagnostic system - Constantly monitors the replica and the mosfet itself. In case of any problems, immediately lets you know what it might be, making troubleshooting much easier. Electronic fuse - Will save your replica and battery in case of a major malfunction. It will automatically disconnect the battery when a short circuit or blocked motor is detected. Programming of all the settings is done solely by using a button and multicolor LED diode mounted in the battery compartment and the trigger. That allows changing the settings in any moment, in a matter of seconds, even under enemy fire. All settings are set independently for each selector position, so you can program the mosfet exactly the way you want, for example semi on semi and binary trigger on auto. Perun for AUG works without problems with any battery from, 7 V to 17 V. It can also be used with most extreme setups.

Perun for G28/HK417 by VFC replaces stock trigger block with our own housing that includes an integrated Clicker and Perun electronic board. It introduces magnetic trigger detection and optical selector, and sector gear detection for the most reliable operation and impressive trigger response. Built-in adjustable Clicker allows to set the trigger exactly according to your preferences in terms of pretravel, overtravel and trigger break force. This Perun kit is the final piece you need to turn your VFC replica into an ultimate airsoft DMR or battle rifle.

Features:

• Selectable firing modes: SEMI ONLY, BINARY, SEMI-AUTO, SEMI-BURST, BURST-AUTO
• Custom cut-off lever, which works with optical sensors for reliable single fire
• Adjustable integrated Clicker with pretravel, overtravel and break force adjustment
• Adjustable trigger sensitivity
• Active brake with adjustable braking power
• Precocking (with spring release feature)
• Rate of fire reduction
• DMR mode
• Low battery voltage alarm
• Programming supported with a multicoloured LED diode
• DSG mode
• Diagnostic system
• Electronic resettable fuse

Feature description

Adjustable integrated Clicker  – Simulating trigger of a real firearm, built-in Clicker requires certain force to be placed on the trigger to “break” it, before a shot can be fire. This force can be set to the user’s preferences, also including reducing it to zero. Pretravel (the leeway before the break is met) and overtravel (the distance that the trigger can travel when it is pulled all the way back) can also be adjusted.

Adjustable trigger sensitivity – The trigger can be set to 8 sensitivity levels for both first and second trigger stage, ranging from short pull needed to fire a shot, to a long one. No modification to the trigger or the gearbox is needed, and the trigger sensitivity change is possible even in the field.

Selectable firing modes – User can choose firing modes available after short or long pull of the trigger: SEMI ONLY, BINARY, SEMI-AUTO, SEMI-BURST, BURST-AUTO.

Active brake – active brake stops the motor after each shot preventing spring compression or in case of replicas with high rate of fire, overspin (double shot problem).

Precocking – Fast trigger response can be a matter of victory or defeat, especially in CQB situations. With precocking enabled, the piston will remain in rear position after each shot with the spring already compressed, ensuring that next shot will be fired immediately after you pull the trigger. To release the spring after using precocking, pull the trigger and hold it for 2 seconds, after which a second shot will be fired, this time with no precocking and fully braked.

Binary trigger – Allows for easy double shots in semi-automatic setting. After enabling this mode, if semi-automatic fire is set, shots will be fired not only when the trigger is pulled, but also when it is released.

Rate of fire reduction – Reduce the rate of fire in automatic or burst fire to save ammo or make the replica shoot in a more realistic fashion.

DMR mode – Required on some fields for DMR replicas. It allows only single shots and within certain time intervals. When enabled, follow-up shots cannot be fired sooner than after 0.25 s, 0.5 s, 1 s, 2 s or 3 s, depending on the chosen setting. It can also be used voluntarily for more realism – to force the shooter to not fire too fast, reflecting the effects of recoil in a real 7.62 mm rifle.

Low battery voltage alarm – Dedicated for Li-Po and Li-Ion batteries. Should the battery voltage fall to a dangerously low level, user will be notified by short sound signals that are repeated every minute. This may also be freely switched on and off.

DSG – a sector gear detection mode specially prepared to work with dual sector gears.

Diagnostic system – Constantly monitors the replica and the MOSFET itself. In case of any problems, it immediately lets you know what it might be, making troubleshooting much easier.

Electronic fuse – Will save your replica and battery in case of a major malfunction. It will automatically disconnect the battery when a short circuit or blocked motor is detected.

Programming of all the settings is done solely by using a button and multicolor LED diode mounted in the battery compartment and the trigger. That allows changing the settings in any moment, in a matter of seconds, even under enemy fire. All settings are set independently for each selector position, so you can program the mosfet exactly the way you want, for example, semi on semi and binary trigger on auto.

Perun for G28 HK417 by VFC works without problems with any battery from, 7 V to 17 V. It can also be used with most extreme setups.

Key specs

• Fits Version 3 gearboxes built to Tokyo Marui standard. Perun has tested it in Arcturus (TM-compatible PE models), D BOYI, CYMA, E&L, G&G, ICS, JG, LCT and Snow Wolf gearboxes. Retro Arms may need minor modification
• Works with any gearset, including DSG, TSG, short-stroked and helical
• Sensing: optical sector gear and selector plate, magnetic trigger
• Battery: 7–17V, with 7.4V, 11.1V or 14.8V Li-Po or Li-Ion recommended. T-Plug (Deans) fitted
• Firing modes: safe, semi, burst (2–5 shots), auto and binary, plus two-stage trigger (semi–burst, semi–auto, burst–auto)
• Active brake (5 levels), precocking (8 levels) and trigger sensitivity (8 levels)
• DMR mode, rate of fire reduction (5 levels), DSG mode and a low-battery alarm for Li-Po and Li-Ion
• Supports brushed and brushless motors
• Electronic resettable fuse and diagnostic LED codes
• Set up with the selector and trigger, guided by sounds and a multicolour LED. No app or tools needed
• Supplied with (per Perun's manual): the unit with T-Plug, 3 spare 1mm magnets, a replacement break magnet, a 1.5mm hex key, 3 selector plate inserts and wire extensions
• Warranty: 24 months from retail purchase

Key specs

• Fits M14s by Tokyo Marui and clones such as CYMA, G&P and Echo 1
• JG M14s are only partly compatible and need some modification
• Not compatible with G&G or Classic Army M14s
• Gears must be compatible with the M14 V7 gearbox
• Battery: 7–17V, with 7.4V, 11.1V or 14.8V Li-Po or Li-Ion recommended. T-Plug (Deans) fitted
• Firing modes: semi, burst (2–5 shots), auto and binary, plus two-stage semi–burst, semi–auto and burst–auto
• Adjustable Clicker break force, pretravel and overtravel, with 8 trigger sensitivity levels
• Active brake, precocking, DMR mode, rate of fire reduction and DSG mode
• Custom cut-off lever, low-battery alarm, diagnostics and an electronic resettable fuse
• Battery in the stock or front grip
• Warranty: 24 months from retail purchase

Perun HPA Trigger Board replaces mechanical contacts in your HPA system and provides lots of useful features. Magnetic sensors eliminate moving parts that are prone to damage, thus increasing reliability. The elasticity of this unit gives you certainty that HPA replica made from parts made by different manufacturers will not have any incompatibility issues. Adaptive trigger control allows switching from a very short trigger travel to a long one even in the field, with almost any trigger, including stock ones.

HPA Trigger Board works with a broad range of Perun accessories for V2 gearbox, like Clicker V2 and V2 PRO or Speeder V2. It only replaces the trigger board and thus does not replace the FCU itself.

Perun HPA Trigger Board replaces mechanical contacts in your HPA system and provides lots of useful features. Magnetic sensors eliminate moving parts that are prone to damage, thus increasing reliability. The elasticity of this unit gives you certainty that HPA replica made from parts made by different manufacturers will not have any incompatibility issues. Adaptive trigger control allows switching from a very short trigger travel to a long one even in the field, with almost any trigger, including stock ones.

HPA Trigger Board works with Perun accessories for V3 gearbox, like Clicker V3.

Based on optical and magnetic sensors – Magnetic trigger sensors ensure that you will no longer have any problems with breaking mechanical switches from stock HPA trigger boards. Optical selector sensors can be calibrated, allowing fast installation and reliable selector operation, including detection of SAFE position and therefore ensuring reliable, electronic safe mode.

Adjustable trigger sensitivity – The trigger can be set to 8 sensitivity levels for both first and second trigger stage, ranging from a very short pull needed to fire a shot, to a long one. No modification to the trigger or the gearbox is needed, and the trigger sensitivity change is possible even in the field.

Diagnostic system – Constantly monitors the board. In case of any problems, it immediately lets you know what it might be, making troubleshooting much easier.

Feature description

Adjustable trigger sensitivity – The trigger can be set to 5 sensitivity levels, ranging from very short pull needed to fire a shot, to a very long one. No modification to the trigger or the gearbox is needed and the trigger sensitivity change is possible even in the field. Independently programmed firing modes - Program the firing modes any way you like, setting safe, semi, burst or auto on both selector positions. Active brake - active brake stops the motor after each shot preventing spring compression or in case of replicas with high rate of fire, overspin (double shot problem). Precocking - Fast trigger response can be a matter of victory or defeat, especially in CQB situations. With precocking enabled, the piston will remain in the rear position after each shot with the spring already compressed, ensuring that the next shot will be fired immediately after you pull the trigger. To release the spring after using precocking, pull the trigger and hold it for 2 seconds, after which a second shot will be fired, this time with no precocking and fully braked. 2-stage trigger – Light trigger pull results with a single shot or burst, while a deeper pull will cause a burst or fully automatic fire. Following modes are available: semi – burst, semi-auto and burst – auto. Binary trigger - Allows for easy double shots in a semi-automatic setting. After enabling this mode, if the semi-automatic fire is set, shots will be fired not only when the trigger is pulled, but also when it is released. Rate of fire reduction - Reduce the rate of fire in automatic or burst fire to save ammo or make the replica shoot in a more realistic fashion. DMR mode - Introduces intervals between semiautomatic shots to comply with DMR rules on some fields. Low battery voltage alarm - Dedicated for Li-Po and Li-Ion batteries. Should the battery voltage fall to a dangerously low level, user will be notified by short sound signals that are repeated every minute. This may also be freely switched on and off. DSG – a sector gear detection mode specially prepared to work with dual-sector gears. Diagnostic system - Constantly monitors the replica and the mosfet itself. In case of any problems, immediately lets you know what it might be, making troubleshooting much easier. Electronic fuse - Will save your replica and battery in case of a major malfunction. It will automatically disconnect the battery when a short circuit or blocked motor is detected.

Programming of all the settings is done solely by using quick and easily memorable sequences of fire selector switching and trigger pulls supported by sound signals and multicolour LED diode. That allows changing the settings in any moment, in a matter of seconds, even under enemy fire. All settings are set independently for each selector position, so you can program the MOSFET exactly the way you want, for example, semi on semi and binary trigger on auto. Perun V2 Hybrid works without problems with any battery from 7V to 17V. It can also be used with the most extreme setups.

Feature description

Adjustable trigger sensitivity – The trigger can be set to 5 sensitivity levels, ranging from very short pull needed to fire a shot, to a very long one. No modification to the trigger or the gearbox is needed and the trigger sensitivity change is possible even in the field. Independently programmed firing modes - Program the firing modes any way you like, setting safe, semi, burst or auto on both selector positions. Active brake - active brake stops the motor after each shot preventing spring compression or in case of replicas with high rate of fire, overspin (double shot problem). Precocking - Fast trigger response can be a matter of victory or defeat, especially in CQB situations. With precocking enabled, the piston will remain in the rear position after each shot with the spring already compressed, ensuring that the next shot will be fired immediately after you pull the trigger. To release the spring after using precocking, pull the trigger and hold it for 2 seconds, after which a second shot will be fired, this time with no precocking and fully braked. 2-stage trigger – Light trigger pull results with a single shot or burst, while a deeper pull will cause a burst or fully automatic fire. Following modes are available: semi – burst, semi-auto and burst – auto. Binary trigger - Allows for easy double shots in a semi-automatic setting. After enabling this mode, if the semi-automatic fire is set, shots will be fired not only when the trigger is pulled, but also when it is released. Rate of fire reduction - Reduce the rate of fire in automatic or burst fire to save ammo or make the replica shoot in a more realistic fashion. DMR mode - Introduces intervals between semiautomatic shots to comply with DMR rules on some fields. Low battery voltage alarm - Dedicated for Li-Po and Li-Ion batteries. Should the battery voltage fall to a dangerously low level, user will be notified by short sound signals that are repeated every minute. This may also be freely switched on and off. DSG – a sector gear detection mode specially prepared to work with dual-sector gears. Diagnostic system - Constantly monitors the replica and the MOSFET itself. In case of any problems, immediately lets you know what it might be, making troubleshooting much easier. Electronic fuse - Will save your replica and battery in case of a major malfunction. It will automatically disconnect the battery when a short circuit or blocked motor is detected.

Programming of all the settings is done solely by using quick and easily memorable sequences of fire selector switching and trigger pulls supported by sound signals and multicolour LED diode. That allows changing the settings in any moment, in a matter of seconds, even under enemy fire. All settings are set independently for each selector position, so you can program the MOSFET exactly the way you want, for example, semi on semi and binary trigger on auto. Perun V3 Hybrid works without problems with any battery from 7V to 17V. It can also be used with the most extreme setups.

Feature description

Adjustable trigger sensitivity – The trigger can be set to 5 sensitivity levels, ranging from very short pull needed to fire a shot, to a very long one. No modification to the trigger or the gearbox is needed and the trigger sensitivity change is possible even in the field. Independently programmed firing modes - Program the firing modes any way you like, setting safe, semi, burst or auto on both selector positions. Active brake - active brake stops the motor after each shot preventing spring compression or in case of replicas with high rate of fire, overspin (double shot problem). Precocking - Fast trigger response can be a matter of victory or defeat, especially in CQB situations. With precocking enabled, the piston will remain in the rear position after each shot with the spring already compressed, ensuring that the next shot will be fired immediately after you pull the trigger. To release the spring after using precocking, pull the trigger and hold it for 2 seconds, after which a second shot will be fired, this time with no precocking and fully braked. 2-stage trigger – Light trigger pull results with a single shot or burst, while a deeper pull will cause a burst or fully automatic fire. Following modes are available: semi – burst, semi-auto and burst – auto. Binary trigger - Allows for easy double shots in a semi-automatic setting. After enabling this mode, if the semi-automatic fire is set, shots will be fired not only when the trigger is pulled, but also when it is released. Rate of fire reduction - Reduce the rate of fire in automatic or burst fire to save ammo or make the replica shoot in a more realistic fashion. DMR mode - Introduces intervals between semiautomatic shots to comply with DMR rules on some fields. Low battery voltage alarm - Dedicated for Li-Po and Li-Ion batteries. Should the battery voltage fall to a dangerously low level, user will be notified by short sound signals that are repeated every minute. This may also be freely switched on and off. DSG – a sector gear detection mode specially prepared to work with dual-sector gears. Diagnostic system - Constantly monitors the replica and the mosfet itself. In case of any problems, immediately lets you know what it might be, making troubleshooting much easier. Electronic fuse - Will save your replica and battery in case of a major malfunction. It will automatically disconnect the battery when a short circuit or blocked motor is detected.

Programming of all the settings is done solely by using quick and easily memorable sequences of fire selector switching and trigger pulls supported by sound signals and multicolour LED diode. That allows changing the settings in any moment, in a matter of seconds, even under enemy fire. All settings are set independently for each selector position, so you can program the MOSFET exactly the way you want, for example, semi on semi and binary trigger on auto. Perun V2 Hybrid works without problems with any battery from 7V to 17V. It can also be used with the most extreme setups.