Airsoft MOSFETs & ETUs

Product description: Mosfet II

Professionally made mosfet designed for airsoft electric guns (AEG).
Device increases gun rate of fire and battery holds longer, than with basic wiring.

SPECIFICATIONS:
- Very small device dimension, it fits nearly everywhere
- Devices without wires, you can use max. 1,5qmm (AWG16) power wires and 0,5qmm (AWG20) signal wires
- Suitable for service center, if you are not familiar with soldering to the circuit board, choose device with wiring and accessories
- Designed for spring up to M210 (equivalent for current 150A single shot fire or 50A burst fire for max. 30s)
- Specified for common batteries up to 17V (Ni-xx 8.4 - 12V, lipol 7.4 - 14.8V)
- 6 wires connection
- Device size 25x12x7mm
- No current consumption in the idle mode
- No sparking on switch contacts
- In auto fire mode piston stops in random position due the mechabox design
- For right function is necessary to have a functional gearbox cut off lever, selector plate, reverse latch, trigger and trigger block, as it has the standard gearbox

DEVICE INSTRUCTIONS: you can download installation manual in English here [PDF, 725.46 kB]
PACKING: device, heat shrink tube and installation manual in English

WARNING: Installation of this device leave to expert, who could solder and disassemble airsoft gun. Never user soldering gun!

WIRING CONNECTION INTO THE GUN:

Modified connection diagram for weapon AUG or P90

Product description: Mosfet - V3

Professionally made mosfet designed for airsoft electric guns (AEG).
Device increases gun rate of fire and battery holds longer, than with basic wiring.
It is fully integrated inside the gearbox version 3 instead of the original trigger contacts, compatible with Tokyo Marui standard.

SPECIFICATIONS:
- Mosfet build on trigger contacts from SHS company
- Easy installation inside the gearbox version 3
- Devices without wires, you can use max. 1,5qmm (AWG16) power wires and 0,5qmm (AWG20) signal wires
- suitable for service center, if you are not familiar with soldering to the circuit board, choose device with wiring and accessories.
- Designed for spring up to M160 (equivalent for current 75A single shot fire or 25A burst fire for max. 30s). For higher load please use Mosfet II (it is outside gearbox)
- Specified for common batteries up to 17V (Ni-xx 8.4 - 12V, lipol 7.4 - 14.8V)
- No current consumption in the idle mode
- No sparking on switch contacts
- In auto fire mode piston stops in random position due the mechabox design
- For right function is necessary to have a functional gearbox cut off lever, selector plate, reverse latch, trigger and trigger block, as it has the standard gearbox

DEVICE INSTRUCTIONS: you can download installation manual in English here [PDF, 674.65 kB]
PACKING:
- mosfet on trigger contacts
- trigger switch
- black heat shrink tube 3,2mm - length 20mm
- installation manual in English

WARNING: Installation of this device leave to expert, who could solder and disassemble airsoft gun. Never user soldering gun!
We can't guarantee 100% compatibility with all gearboxes, but Mosfet - V3 will fit into standard and common brand's gearboxes without larger modifications.

WIRING CONNECTION INTO THE GUN:

Modified connection diagram for AUG weapon

Product description: AEP Mosfet

Professionally made mosfet designed for airsoft electric pistols (AEP).
Device increases gun rate of fire and battery holds longer, than with basic wiring.
Can be installed without modifications into these AEP:
Cyma CM.030 Glock 18C
Cyma CM.121 Desert Eagle
Cyma CM.122 SIG P226
Cyma CM.123 Colt M1911
Cyma CM.125 H&K USP
Cyma CM.126 Beretta M92F
Cyma CM.127 Phantom
Cyma CM.128 HI-CAPA 5.1
Tokyo Marui Glock 18C AEP
Tokyo Marui Beretta M93R AEP
Tokyo Marui Beretta M9A1 AEP
Tokyo Marui HK USP AEP
Umarex HK USP AEP
Double Eagle M81 USP

RECOMMENDED BATTERY:
1. Lipol 7.4v (2S) Turnigy Nano-Tech Plus 300mAh 70C~140C
2. Lipol 7.4v (2S) Turnigy nano-tech 300mah 45~90C
3. Lipol 7.4v (2S) Turnigy nano-tech 300mAh 35~70C

SPECIFICATIONS:
- Very small device dimension - used Micro mosfet II
- Prepared wiring allows fast and easy installation into the pistol. Simply solder wires to the motor and trigger contacts
- On the devices are pre-soldered high quality power wires 0,5 qmm (AWG20) with silicone insulation (length 210mm from mosfet) and blue wires 0.25 qmm (AWG24) with PVC insulation (length 110mm from mosfet)
- Connector for battery is used JST-SYR 2 pin
- Board covered by conformal coating, it protect device against water
- If you want to use your own wires or connector, choose Micro mosfet II without wiring
- Can be used with any AEP upgrade, because it was designed for spring up to M160 (equivalent for current 75A single shot fire or 25A burst fire for max. 30s)
- Recomended to use 7,4V lipol battery, but device is specified for common batteries up to 17V (Ni-xx 8.4 - 12V, lipol 7.4 - 14.8V)
- 6 wires connection
- Device size 15x7x5mm
- No current consumption in the idle mode
- No sparking on switch contacts
- In auto fire mode piston stops in random position due the mechabox design
- For right function is necessary to have a functional gearbox cut off lever, selector plate, reverse latch, trigger and trigger block, as it has the standard gearbox

DEVICE INSTRUCTIONS: you can download installation manual in English here [PDF, 814.61 kB]
PACKING:
- Device with wiring and JST-SYR connector
- Installation manual in English

WARNING: Installation of this device leaves to expert, who could solder and disassemble airsoft pistol. Never user soldering gun!

WIRING CONNECTION INTO THE GUN:

Product description: Micro active brake II with wiring

Professionally made mosfet with motor active braking designed for airsoft electric guns (AEG).
In semi fire mode piston isn't partially stretched, spring is fully released, parts in mechabox aren't under strain and nozzle locks hop-up chamber in greater part (depends on ROF).
Active break solves multiple shots in semi mode with weapons with a very high rate of fire (ROF).
Device increases gun rate of fire and battery holds longer, than with basic wiring.

SPECIFICATIONS:
- Very small device dimension, it fits nearly everywhere
- Pre soldered wires allow faster and easier installation into the gun, it is long enough for all kind of weapons. Simply cut wires to the required length and attach connectors (included in package)
-- There are high quality power wires 1,5 qmm (AWG16) with thin and hard MPPE insulation and signal blue wire 0.34 qmm (AWG22) with MPPE insulation
- Board covered by conformal coating, it protect device against water
- If you want to use your own wires, choose variant without wiring
- Designed for spring up to M160 (equivalent for current 75A single shot fire or 25A burst fire for max. 30s)
- Specified for common batteries up to 17V (Ni-xx 8.4 - 12V, lipol 7.4 - 14.8V)
- Active braking uses the excess energy from the motor to stop it. The braking effect is the most powerful with high torgue motor
- 6 wires connection
- Device size 27x10x7mm
- No current consumption in the idle mode
- No sparking on switch contacts
- In auto fire mode piston stops in random position due the mechabox design
- For right function is necessary to have a functional gearbox cut off lever, selector plate, reverse latch, trigger and trigger block, as it has the standard gearbox

DEVICE INSTRUCTIONS: you can download installation manual in English here [PDF, 596.09 kB]
PACKING:
- Device with wiring
- DeanT connector male
- 30A mini fuse
- 4x faston female 2,8mm
- 6x black heat shrink tube 3,2mm - length 20mm
- 3x black heat shrink tube 4,8mm - length 20mm
- Installation manual in English

WARNING: Installation of this device leave to expert, who could solder and disassemble airsoft gun. Never user soldering gun!

WIRING CONNECTION INTO THE GUN:

Modified connection diagram for weapon AUG or P90

Product description: Active brake II with wiring

Professionally made mosfet with motor active braking designed for airsoft electric guns (AEG).
In semi fire mode piston isn't partially stretched, spring is fully released, parts in mechabox aren't under strain and nozzle locks hop-up chamber in greater part (depends on ROF).
Active break solves multiple shots in semi mode with weapons with very high rate of fire (ROF).
Device increases gun rate of fire and battery holds longer, than with basic wiring.

SPECIFICATIONS:
- Presoldered wires allows faster and easier installation into the gun, it is long enough for all kind of weapons. Simply cut wires to the required length and attach connectors (included in package)
- On the devices are presoldered four high quality 1,5qmm (AWG16) power wires covered with MPPE insulation and two 0,34qmm (AWG22) signal wires
- Board covered by conformal coating, it protect device against water
- If you want to use your own wires, choose variant without wiring
- Designed for spring up to M210 (equivalent for current 150A single shot fire or 50A burst fire for max. 30s)
- Specified for common batteries up to 17V (Ni-xx 8.4 - 12V, lipol 7.4 - 14.8V)
- Active braking uses the excess energy from the motor to stop it. The braking effect is the most powerful with high torgue motor
- 6 wires connection
- Device size 35x12x7mm
- No current consumption in the idle mode
- No sparking on switch contacts
- In auto fire mode piston stops in random position due the mechabox design
- For right function is necessary to have a functional gearbox cut off lever, selector plate, reverse latch, trigger and trigger block, as it has the standard gearbox

DEVICE INSTRUCTIONS: you can download installation manual in English here [PDF, 663.23 kB]
PACKING:
- Device with wiring
- DeanT connector male
- 30A mini fuse
- 4x faston female 2,8mm
- 6x black heat shrink tube 3,2mm - length 20mm
- 3x black heat shrink tube 4,8mm - length 20mm
- Installation manual in English

WARNING: Installation of this device leave to expert, who could solder and disassemble airsoft gun. Never user soldering gun!

WIRING CONNECTION INTO THE GUN:

Modified connection diagram for weapon AUG or P90

Product description: Switch brake

Professionally made mosfet with active braking, which can be disabled by removing red jumper.
Device is designed to replace microswitch in the specific gearbox V2.
There is no modification needed.
In semi fire mode piston isn't partially stretched, spring is fully released, parts in mechabox aren't under strain and nozzle locks hop-up chamber in greater part (depends on ROF).
Active break solves multiple shots in semi mode with weapons with very high rate of fire (ROF).
Device increases gun rate of fire and battery holds longer, than with basic wiring.

SPECIFICATIONS:
- Easy installation inside the gearbox version 2, which replace microswitch
- Devices without wires, you can use max. 1,5qmm (AWG16) power wires and 0,5qmm (AWG20) signal wires
- Suitable for service center, if you are not familiar with soldering to the circuit board, choose device with wiring and accessories
- Disable active braking by unplugging red jumper, when you gun has Rate of fire under 20bb/s, otherwise it could lock up trigger on SEMI due too low gear speed.
- Motor will be under less stress without active braking.
- Designed for spring up to M160 (equivalent for current 75A single shot fire or 25A burst fire for max. 30s)
- Specified for common batteries up to 17V (Ni-xx 8.4 - 12V, lipol 7.4 - 14.8V)
- Active braking uses the excess energy from the motor to stop it. The braking effect is the most powerful with high torgue motor
- In auto fire mode piston stops in random position due the mechabox design
- For right function is necessary to have a functional gearbox cut off lever, selector plate, reverse latch, trigger and trigger block, as it has the standard gearbox

DEVICE INSTRUCTIONS: you can download an installation manual in English here [1.27 MB]
PACKING: device and installation manual in English

WARNING: Installation of this device leave to expert, who could solder and disassemble airsoft gun. Never user soldering gun!

WIRING CONNECTION INTO THE GUN:

AUG Perun for AUG mechanical contacts in your AUG replica and provides lots of useful features. Magnetic sensors coupled with a magnet installed directly on the trigger, allow to remove the bar that connects trigger with the gearbox, making trigger pull much smoother. Optical detection of the sector gear position ensures a reliable single-fire function. Only replicas in Tokyo Marui standard are compatible with this mosfet, among which are those manufactured by: Tokyo Marui, Classic Army, JG, ASG.    

Feature description Adjustable trigger sensitivity – The trigger can be set to 5 sensitivity levels for both first and second trigger stage, ranging from short pull needed to fire a shot, to a long one. No modification to the trigger or the gearbox is needed and the trigger sensitivity change is possible even in the field. Selectable firing modes – User can choose firing modes available after short or long pull of the trigger: SEMI ONLY, BINARY, SEMI-AUTO, SEMI-BURST, BURST-AUTO. Active brake - active brake stops the motor after each shot preventing spring compression or in case of replicas with high rate of fire, overspin (double shot problem). Precocking - Fast trigger response can be a matter of victory or defeat, especially in CQB situations. With precocking enabled, piston will remain in rear position after each shot with the spring already compressed, ensuring that next shot will be fired immediately after you pull the trigger. To release the spring after using precocking, pull the trigger and hold it for 2 seconds, after which a second shot will be fired, this time with no precocking and fully braked. Binary trigger - Allows for easy double shots in semi-automatic setting. After enabling this mode, if semi-automatic fire is set, shots will be fired not only when the trigger is pulled, but also when it is released. Rate of fire reduction - Reduce the rate of fire in automatic or burst fire to save ammo or make the replica shoot in a more realistic fashion. Low battery voltage alarm - Dedicated for Li-Po and Li-Ion batteries. Should the battery voltage fall to a dangerously low level, user will be notified by short sound signals that are repeated every minute. This may also be freely switched on and off. DSG – a sector gear detection mode specially prepared to work with dual sector gears. Diagnostic system - Constantly monitors the replica and the mosfet itself. In case of any problems, immediately lets you know what it might be, making troubleshooting much easier. Electronic fuse - Will save your replica and battery in case of a major malfunction. It will automatically disconnect the battery when a short circuit or blocked motor is detected. Programming of all the settings is done solely by using a button and multicolor LED diode mounted in the battery compartment and the trigger. That allows changing the settings in any moment, in a matter of seconds, even under enemy fire. All settings are set independently for each selector position, so you can program the mosfet exactly the way you want, for example semi on semi and binary trigger on auto. Perun for AUG works without problems with any battery from, 7 V to 17 V. It can also be used with most extreme setups.

• Shooting mode (burst/binary),

• DMR cooldown,

• ROF setting, pre-cocking,

• Sleep mode,

• Active braking,

• Battery protection.

• Mechanical blocking safety shutdown

• Mosfet temperature safety protection

Perun for G28/HK417 by VFC replaces stock trigger block with our own housing that includes an integrated Clicker and Perun electronic board. It introduces magnetic trigger detection and optical selector, and sector gear detection for the most reliable operation and impressive trigger response. Built-in adjustable Clicker allows to set the trigger exactly according to your preferences in terms of pretravel, overtravel and trigger break force. This Perun kit is the final piece you need to turn your VFC replica into an ultimate airsoft DMR or battle rifle.

Features:

• Selectable firing modes: SEMI ONLY, BINARY, SEMI-AUTO, SEMI-BURST, BURST-AUTO
• Custom cut-off lever, which works with optical sensors for reliable single fire
• Adjustable integrated Clicker with pretravel, overtravel and break force adjustment
• Adjustable trigger sensitivity
• Active brake with adjustable braking power
• Precocking (with spring release feature)
• Rate of fire reduction
• DMR mode
• Low battery voltage alarm
• Programming supported with a multicoloured LED diode
• DSG mode
• Diagnostic system
• Electronic resettable fuse

Feature description

Adjustable integrated Clicker  – Simulating trigger of a real firearm, built-in Clicker requires certain force to be placed on the trigger to “break” it, before a shot can be fire. This force can be set to the user’s preferences, also including reducing it to zero. Pretravel (the leeway before the break is met) and overtravel (the distance that the trigger can travel when it is pulled all the way back) can also be adjusted.

Adjustable trigger sensitivity – The trigger can be set to 8 sensitivity levels for both first and second trigger stage, ranging from short pull needed to fire a shot, to a long one. No modification to the trigger or the gearbox is needed, and the trigger sensitivity change is possible even in the field.

Selectable firing modes – User can choose firing modes available after short or long pull of the trigger: SEMI ONLY, BINARY, SEMI-AUTO, SEMI-BURST, BURST-AUTO.

Active brake – active brake stops the motor after each shot preventing spring compression or in case of replicas with high rate of fire, overspin (double shot problem).

Precocking – Fast trigger response can be a matter of victory or defeat, especially in CQB situations. With precocking enabled, the piston will remain in rear position after each shot with the spring already compressed, ensuring that next shot will be fired immediately after you pull the trigger. To release the spring after using precocking, pull the trigger and hold it for 2 seconds, after which a second shot will be fired, this time with no precocking and fully braked.

Binary trigger – Allows for easy double shots in semi-automatic setting. After enabling this mode, if semi-automatic fire is set, shots will be fired not only when the trigger is pulled, but also when it is released.

Rate of fire reduction – Reduce the rate of fire in automatic or burst fire to save ammo or make the replica shoot in a more realistic fashion.

DMR mode – Required on some fields for DMR replicas. It allows only single shots and within certain time intervals. When enabled, follow-up shots cannot be fired sooner than after 0.25 s, 0.5 s, 1 s, 2 s or 3 s, depending on the chosen setting. It can also be used voluntarily for more realism – to force the shooter to not fire too fast, reflecting the effects of recoil in a real 7.62 mm rifle.

Low battery voltage alarm – Dedicated for Li-Po and Li-Ion batteries. Should the battery voltage fall to a dangerously low level, user will be notified by short sound signals that are repeated every minute. This may also be freely switched on and off.

DSG – a sector gear detection mode specially prepared to work with dual sector gears.

Diagnostic system – Constantly monitors the replica and the MOSFET itself. In case of any problems, it immediately lets you know what it might be, making troubleshooting much easier.

Electronic fuse – Will save your replica and battery in case of a major malfunction. It will automatically disconnect the battery when a short circuit or blocked motor is detected.

Programming of all the settings is done solely by using a button and multicolor LED diode mounted in the battery compartment and the trigger. That allows changing the settings in any moment, in a matter of seconds, even under enemy fire. All settings are set independently for each selector position, so you can program the mosfet exactly the way you want, for example, semi on semi and binary trigger on auto.

Perun for G28 HK417 by VFC works without problems with any battery from, 7 V to 17 V. It can also be used with most extreme setups.

Perun HPA Trigger Board replaces mechanical contacts in your HPA system and provides lots of useful features. Magnetic sensors eliminate moving parts that are prone to damage, thus increasing reliability. The elasticity of this unit gives you certainty that HPA replica made from parts made by different manufacturers will not have any incompatibility issues. Adaptive trigger control allows switching from a very short trigger travel to a long one even in the field, with almost any trigger, including stock ones.

HPA Trigger Board works with a broad range of Perun accessories for V2 gearbox, like Clicker V2 and V2 PRO or Speeder V2. It only replaces the trigger board and thus does not replace the FCU itself.

Perun HPA Trigger Board replaces mechanical contacts in your HPA system and provides lots of useful features. Magnetic sensors eliminate moving parts that are prone to damage, thus increasing reliability. The elasticity of this unit gives you certainty that HPA replica made from parts made by different manufacturers will not have any incompatibility issues. Adaptive trigger control allows switching from a very short trigger travel to a long one even in the field, with almost any trigger, including stock ones.

HPA Trigger Board works with Perun accessories for V3 gearbox, like Clicker V3.

Based on optical and magnetic sensors – Magnetic trigger sensors ensure that you will no longer have any problems with breaking mechanical switches from stock HPA trigger boards. Optical selector sensors can be calibrated, allowing fast installation and reliable selector operation, including detection of SAFE position and therefore ensuring reliable, electronic safe mode.

Adjustable trigger sensitivity – The trigger can be set to 8 sensitivity levels for both first and second trigger stage, ranging from a very short pull needed to fire a shot, to a long one. No modification to the trigger or the gearbox is needed, and the trigger sensitivity change is possible even in the field.

Diagnostic system – Constantly monitors the board. In case of any problems, it immediately lets you know what it might be, making troubleshooting much easier.

Key specs

• Fits M14s by Tokyo Marui and clones such as CYMA, G&P and Echo 1
• JG M14s are only partly compatible and need some modification
• Not compatible with G&G or Classic Army M14s
• Gears must be compatible with the M14 V7 gearbox
• Battery: 7–17V, with 7.4V, 11.1V or 14.8V Li-Po or Li-Ion recommended. T-Plug (Deans) fitted
• Firing modes: semi, burst (2–5 shots), auto and binary, plus two-stage semi–burst, semi–auto and burst–auto
• Adjustable Clicker break force, pretravel and overtravel, with 8 trigger sensitivity levels
• Active brake, precocking, DMR mode, rate of fire reduction and DSG mode
• Custom cut-off lever, low-battery alarm, diagnostics and an electronic resettable fuse
• Battery in the stock or front grip
• Warranty: 24 months from retail purchase

Key specs

• Fits Version 3 gearboxes built to Tokyo Marui standard. Perun has tested it in Arcturus (TM-compatible PE models), D BOYI, CYMA, E&L, G&G, ICS, JG, LCT and Snow Wolf gearboxes. Retro Arms may need minor modification
• Works with any gearset, including DSG, TSG, short-stroked and helical
• Sensing: optical sector gear and selector plate, magnetic trigger
• Battery: 7–17V, with 7.4V, 11.1V or 14.8V Li-Po or Li-Ion recommended. T-Plug (Deans) fitted
• Firing modes: safe, semi, burst (2–5 shots), auto and binary, plus two-stage trigger (semi–burst, semi–auto, burst–auto)
• Active brake (5 levels), precocking (8 levels) and trigger sensitivity (8 levels)
• DMR mode, rate of fire reduction (5 levels), DSG mode and a low-battery alarm for Li-Po and Li-Ion
• Supports brushed and brushless motors
• Electronic resettable fuse and diagnostic LED codes
• Set up with the selector and trigger, guided by sounds and a multicolour LED. No app or tools needed
• Supplied with (per Perun's manual): the unit with T-Plug, 3 spare 1mm magnets, a replacement break magnet, a 1.5mm hex key, 3 selector plate inserts and wire extensions
• Warranty: 24 months from retail purchase

Feature description

Adjustable trigger sensitivity – The trigger can be set to 5 sensitivity levels, ranging from very short pull needed to fire a shot, to a very long one. No modification to the trigger or the gearbox is needed and the trigger sensitivity change is possible even in the field. Independently programmed firing modes - Program the firing modes any way you like, setting safe, semi, burst or auto on both selector positions. Active brake - active brake stops the motor after each shot preventing spring compression or in case of replicas with high rate of fire, overspin (double shot problem). Precocking - Fast trigger response can be a matter of victory or defeat, especially in CQB situations. With precocking enabled, the piston will remain in the rear position after each shot with the spring already compressed, ensuring that the next shot will be fired immediately after you pull the trigger. To release the spring after using precocking, pull the trigger and hold it for 2 seconds, after which a second shot will be fired, this time with no precocking and fully braked. 2-stage trigger – Light trigger pull results with a single shot or burst, while a deeper pull will cause a burst or fully automatic fire. Following modes are available: semi – burst, semi-auto and burst – auto. Binary trigger - Allows for easy double shots in a semi-automatic setting. After enabling this mode, if the semi-automatic fire is set, shots will be fired not only when the trigger is pulled, but also when it is released. Rate of fire reduction - Reduce the rate of fire in automatic or burst fire to save ammo or make the replica shoot in a more realistic fashion. DMR mode - Introduces intervals between semiautomatic shots to comply with DMR rules on some fields. Low battery voltage alarm - Dedicated for Li-Po and Li-Ion batteries. Should the battery voltage fall to a dangerously low level, user will be notified by short sound signals that are repeated every minute. This may also be freely switched on and off. DSG – a sector gear detection mode specially prepared to work with dual-sector gears. Diagnostic system - Constantly monitors the replica and the mosfet itself. In case of any problems, immediately lets you know what it might be, making troubleshooting much easier. Electronic fuse - Will save your replica and battery in case of a major malfunction. It will automatically disconnect the battery when a short circuit or blocked motor is detected.

Programming of all the settings is done solely by using quick and easily memorable sequences of fire selector switching and trigger pulls supported by sound signals and multicolour LED diode. That allows changing the settings in any moment, in a matter of seconds, even under enemy fire. All settings are set independently for each selector position, so you can program the MOSFET exactly the way you want, for example, semi on semi and binary trigger on auto. Perun V2 Hybrid works without problems with any battery from 7V to 17V. It can also be used with the most extreme setups.

Feature description

Adjustable trigger sensitivity – The trigger can be set to 5 sensitivity levels, ranging from very short pull needed to fire a shot, to a very long one. No modification to the trigger or the gearbox is needed and the trigger sensitivity change is possible even in the field. Independently programmed firing modes - Program the firing modes any way you like, setting safe, semi, burst or auto on both selector positions. Active brake - active brake stops the motor after each shot preventing spring compression or in case of replicas with high rate of fire, overspin (double shot problem). Precocking - Fast trigger response can be a matter of victory or defeat, especially in CQB situations. With precocking enabled, the piston will remain in the rear position after each shot with the spring already compressed, ensuring that the next shot will be fired immediately after you pull the trigger. To release the spring after using precocking, pull the trigger and hold it for 2 seconds, after which a second shot will be fired, this time with no precocking and fully braked. 2-stage trigger – Light trigger pull results with a single shot or burst, while a deeper pull will cause a burst or fully automatic fire. Following modes are available: semi – burst, semi-auto and burst – auto. Binary trigger - Allows for easy double shots in a semi-automatic setting. After enabling this mode, if the semi-automatic fire is set, shots will be fired not only when the trigger is pulled, but also when it is released. Rate of fire reduction - Reduce the rate of fire in automatic or burst fire to save ammo or make the replica shoot in a more realistic fashion. DMR mode - Introduces intervals between semiautomatic shots to comply with DMR rules on some fields. Low battery voltage alarm - Dedicated for Li-Po and Li-Ion batteries. Should the battery voltage fall to a dangerously low level, user will be notified by short sound signals that are repeated every minute. This may also be freely switched on and off. DSG – a sector gear detection mode specially prepared to work with dual-sector gears. Diagnostic system - Constantly monitors the replica and the mosfet itself. In case of any problems, immediately lets you know what it might be, making troubleshooting much easier. Electronic fuse - Will save your replica and battery in case of a major malfunction. It will automatically disconnect the battery when a short circuit or blocked motor is detected.

Programming of all the settings is done solely by using quick and easily memorable sequences of fire selector switching and trigger pulls supported by sound signals and multicolour LED diode. That allows changing the settings in any moment, in a matter of seconds, even under enemy fire. All settings are set independently for each selector position, so you can program the MOSFET exactly the way you want, for example, semi on semi and binary trigger on auto. Perun V2 Hybrid works without problems with any battery from 7V to 17V. It can also be used with the most extreme setups.

Feature description

Adjustable trigger sensitivity – The trigger can be set to 5 sensitivity levels, ranging from very short pull needed to fire a shot, to a very long one. No modification to the trigger or the gearbox is needed and the trigger sensitivity change is possible even in the field. Independently programmed firing modes - Program the firing modes any way you like, setting safe, semi, burst or auto on both selector positions. Active brake - active brake stops the motor after each shot preventing spring compression or in case of replicas with high rate of fire, overspin (double shot problem). Precocking - Fast trigger response can be a matter of victory or defeat, especially in CQB situations. With precocking enabled, the piston will remain in the rear position after each shot with the spring already compressed, ensuring that the next shot will be fired immediately after you pull the trigger. To release the spring after using precocking, pull the trigger and hold it for 2 seconds, after which a second shot will be fired, this time with no precocking and fully braked. 2-stage trigger – Light trigger pull results with a single shot or burst, while a deeper pull will cause a burst or fully automatic fire. Following modes are available: semi – burst, semi-auto and burst – auto. Binary trigger - Allows for easy double shots in a semi-automatic setting. After enabling this mode, if the semi-automatic fire is set, shots will be fired not only when the trigger is pulled, but also when it is released. Rate of fire reduction - Reduce the rate of fire in automatic or burst fire to save ammo or make the replica shoot in a more realistic fashion. DMR mode - Introduces intervals between semiautomatic shots to comply with DMR rules on some fields. Low battery voltage alarm - Dedicated for Li-Po and Li-Ion batteries. Should the battery voltage fall to a dangerously low level, user will be notified by short sound signals that are repeated every minute. This may also be freely switched on and off. DSG – a sector gear detection mode specially prepared to work with dual-sector gears. Diagnostic system - Constantly monitors the replica and the MOSFET itself. In case of any problems, immediately lets you know what it might be, making troubleshooting much easier. Electronic fuse - Will save your replica and battery in case of a major malfunction. It will automatically disconnect the battery when a short circuit or blocked motor is detected.

Programming of all the settings is done solely by using quick and easily memorable sequences of fire selector switching and trigger pulls supported by sound signals and multicolour LED diode. That allows changing the settings in any moment, in a matter of seconds, even under enemy fire. All settings are set independently for each selector position, so you can program the MOSFET exactly the way you want, for example, semi on semi and binary trigger on auto. Perun V3 Hybrid works without problems with any battery from 7V to 17V. It can also be used with the most extreme setups.