Jefftron

Product description: Mosfet - V2

Professionally made mosfet designed for airsoft electric guns (AEG).
Device increases gun rate of fire and battery holds longer, than with basic wiring.
It is fully integrated inside the gearbox version 2 instead of the original trigger contacts, compatible with Tokyo Marui standard.

SPECIFICATIONS:
- Mosfet build on trigger contacts from SHS company
- Easy installation inside the gearbox version 2
- Devices without wires, you can use max. 1,5qmm (AWG16) power wires and 0,5qmm (AWG20) signal wires
- suitable for service center, if you are not familiar with soldering to the circuit board, choose device with wiring and accessories.
- Designed for spring up to M160 (equivalent for current 75A single shot fire or 25A burst fire for max. 30s). For higher load please use Mosfet II (it is outside gearbox)
- Specified for common batteries up to 17V (Ni-xx 8.4 - 12V, lipol 7.4 - 14.8V)
- No current consumption in the idle mode
- No sparking on switch contacts
- In auto fire mode piston stops in random position due the mechabox design
- For right function is necessary to have a functional gearbox cut off lever, selector plate, reverse latch, trigger and trigger block, as it has the standard gearbox

DEVICE INSTRUCTIONS: you can download installation manual in English here [PDF, 674.65 kB]
PACKING: Mosfet on trigger contacts, trigger switch, screw, pad (for screw to keep device in the position) and installation manual in English

WARNING: Installation of this device leave to expert, who could solder and disassemble airsoft gun. Never user soldering gun!
We can't guarantee 100% compatibility with all gearboxes, but Mosfet - V2 will fit into standard and common brand's gearboxes without larger modifications.

WIRING CONNECTION INTO THE GUN:

Product description: Mosfet II

Professionally made mosfet designed for airsoft electric guns (AEG).
Device increases gun rate of fire and battery holds longer, than with basic wiring.

SPECIFICATIONS:
- Very small device dimension, it fits nearly everywhere
- Devices without wires, you can use max. 1,5qmm (AWG16) power wires and 0,5qmm (AWG20) signal wires
- Suitable for service center, if you are not familiar with soldering to the circuit board, choose device with wiring and accessories
- Designed for spring up to M210 (equivalent for current 150A single shot fire or 50A burst fire for max. 30s)
- Specified for common batteries up to 17V (Ni-xx 8.4 - 12V, lipol 7.4 - 14.8V)
- 6 wires connection
- Device size 25x12x7mm
- No current consumption in the idle mode
- No sparking on switch contacts
- In auto fire mode piston stops in random position due the mechabox design
- For right function is necessary to have a functional gearbox cut off lever, selector plate, reverse latch, trigger and trigger block, as it has the standard gearbox

DEVICE INSTRUCTIONS: you can download installation manual in English here [PDF, 725.46 kB]
PACKING: device, heat shrink tube and installation manual in English

WARNING: Installation of this device leave to expert, who could solder and disassemble airsoft gun. Never user soldering gun!

WIRING CONNECTION INTO THE GUN:

Modified connection diagram for weapon AUG or P90

Product description: Mosfet II with wiring

Professionally made mosfet designed for airsoft electric guns (AEG).
Device increases gun rate of fire and battery holds longer, than with basic wiring.

SPECIFICATIONS:
- Presoldered wires allows faster and easier installation into the gun, it is long enough for all kind of weapons. Simply cut wires to the required length and attach connectors (included in package)
- On the devices are presoldered four high quality 1,5qmm (AWG16) power wires covered with MPPE insulation and two 0,34qmm (AWG22) signal wires
- Board covered by conformal coating, it protect device against water
- If you want to use your own wires, choose variant without wiring
- Designed for spring up to M210 (equivalent for current 150A single shot fire or 50A burst fire for max. 30s)
- Specified for common batteries up to 17V (Ni-xx 8.4 - 12V, lipol 7.4 - 14.8V)
- 6 wires connection
- Device size 25x12x7mm
- No current consumption in the idle mode
- No sparking on switch contacts
- In auto fire mode piston stops in random position due the mechabox design
- For right function is necessary to have a functional gearbox cut off lever, selector plate, reverse latch, trigger and trigger block, as it has the standard gearbox

DEVICE INSTRUCTIONS: you can download installation manual in English here [PDF, 685.43 kB]
PACKING:
- Device with wiring
- DeanT connector male
- 30A mini fuse
- 4x faston female 2,8mm
- 6x black heat shrink tube 3,2mm - length 20mm
- 3x black heat shrink tube 4,8mm - length 20mm
- Installation manual in English

WARNING: Installation of this device leave to expert, who could solder and disassemble airsoft gun. Never user soldering gun!

WIRING CONNECTION INTO THE GUN:

Modified connection diagram for weapon AUG or P90

Product description: Mosfet - V3

Professionally made mosfet designed for airsoft electric guns (AEG).
Device increases gun rate of fire and battery holds longer, than with basic wiring.
It is fully integrated inside the gearbox version 3 instead of the original trigger contacts, compatible with Tokyo Marui standard.

SPECIFICATIONS:
- Mosfet build on trigger contacts from SHS company
- Easy installation inside the gearbox version 3
- Devices without wires, you can use max. 1,5qmm (AWG16) power wires and 0,5qmm (AWG20) signal wires
- suitable for service center, if you are not familiar with soldering to the circuit board, choose device with wiring and accessories.
- Designed for spring up to M160 (equivalent for current 75A single shot fire or 25A burst fire for max. 30s). For higher load please use Mosfet II (it is outside gearbox)
- Specified for common batteries up to 17V (Ni-xx 8.4 - 12V, lipol 7.4 - 14.8V)
- No current consumption in the idle mode
- No sparking on switch contacts
- In auto fire mode piston stops in random position due the mechabox design
- For right function is necessary to have a functional gearbox cut off lever, selector plate, reverse latch, trigger and trigger block, as it has the standard gearbox

DEVICE INSTRUCTIONS: you can download installation manual in English here [PDF, 674.65 kB]
PACKING:
- mosfet on trigger contacts
- trigger switch
- black heat shrink tube 3,2mm - length 20mm
- installation manual in English

WARNING: Installation of this device leave to expert, who could solder and disassemble airsoft gun. Never user soldering gun!
We can't guarantee 100% compatibility with all gearboxes, but Mosfet - V3 will fit into standard and common brand's gearboxes without larger modifications.

WIRING CONNECTION INTO THE GUN:

Modified connection diagram for AUG weapon

Product description: AEP Mosfet

Professionally made mosfet designed for airsoft electric pistols (AEP).
Device increases gun rate of fire and battery holds longer, than with basic wiring.
Can be installed without modifications into these AEP:
Cyma CM.030 Glock 18C
Cyma CM.121 Desert Eagle
Cyma CM.122 SIG P226
Cyma CM.123 Colt M1911
Cyma CM.125 H&K USP
Cyma CM.126 Beretta M92F
Cyma CM.127 Phantom
Cyma CM.128 HI-CAPA 5.1
Tokyo Marui Glock 18C AEP
Tokyo Marui Beretta M93R AEP
Tokyo Marui Beretta M9A1 AEP
Tokyo Marui HK USP AEP
Umarex HK USP AEP
Double Eagle M81 USP

RECOMMENDED BATTERY:
1. Lipol 7.4v (2S) Turnigy Nano-Tech Plus 300mAh 70C~140C
2. Lipol 7.4v (2S) Turnigy nano-tech 300mah 45~90C
3. Lipol 7.4v (2S) Turnigy nano-tech 300mAh 35~70C

SPECIFICATIONS:
- Very small device dimension - used Micro mosfet II
- Prepared wiring allows fast and easy installation into the pistol. Simply solder wires to the motor and trigger contacts
- On the devices are pre-soldered high quality power wires 0,5 qmm (AWG20) with silicone insulation (length 210mm from mosfet) and blue wires 0.25 qmm (AWG24) with PVC insulation (length 110mm from mosfet)
- Connector for battery is used JST-SYR 2 pin
- Board covered by conformal coating, it protect device against water
- If you want to use your own wires or connector, choose Micro mosfet II without wiring
- Can be used with any AEP upgrade, because it was designed for spring up to M160 (equivalent for current 75A single shot fire or 25A burst fire for max. 30s)
- Recomended to use 7,4V lipol battery, but device is specified for common batteries up to 17V (Ni-xx 8.4 - 12V, lipol 7.4 - 14.8V)
- 6 wires connection
- Device size 15x7x5mm
- No current consumption in the idle mode
- No sparking on switch contacts
- In auto fire mode piston stops in random position due the mechabox design
- For right function is necessary to have a functional gearbox cut off lever, selector plate, reverse latch, trigger and trigger block, as it has the standard gearbox

DEVICE INSTRUCTIONS: you can download installation manual in English here [PDF, 814.61 kB]
PACKING:
- Device with wiring and JST-SYR connector
- Installation manual in English

WARNING: Installation of this device leaves to expert, who could solder and disassemble airsoft pistol. Never user soldering gun!

WIRING CONNECTION INTO THE GUN:

Product description: Mosfet - V3 Solo

Professionally made mosfet designed for airsoft electric guns (AEG) with V3 gearbox.
Device increases gun rate of fire and battery holds longer, than with basic wiring.
It is for trigger contacts of the gearbox version 3 compatible with Tokyo Marui standard.

SPECIFICATIONS:
- It is necessary to modify the trigger contacts according to the manual
- Devices without wires, you can use max. 1,5qmm (AWG16) power wires and 0,5qmm (AWG20) signal wires
- Suitable for service center, if you are not familiar with soldering to the circuit board, choose device with wiring or complete wiring above the gearbox.
- Designed for spring up to M160 (equivalent for current 75A single shot fire or 25A burst fire for max. 30s). For higher load please use Mosfet II (it is outside gearbox)
- Specified for common batteries up to 17V (Ni-xx 8.4 - 12V, lipol 7.4 - 14.8V)
- No current consumption in the idle mode
- No sparking on switch contacts
- In auto fire mode piston stops in random position due the mechabox design
- For right function is necessary to have a functional gearbox cut off lever, selector plate, reverse latch, trigger and trigger block, as it has the standard gearbox

DEVICE INSTRUCTIONS: you can download installation manual in English here [PDF, 2.02 MB]
PACKING:
- mosfet for trigger contacts V3
- installation manual in English

WARNING: Installation of this device leave to expert, who could solder and disassemble airsoft gun. Never user soldering gun!
We can't guarantee 100% compatibility with all trigger contacts, but Mosfet - V3 Solo will fit into standard and common brand's without larger modifications.

WIRING CONNECTION INTO THE GUN:

Modified connection diagram for AUG weapon

Product description: Micro active brake II with wiring

Professionally made mosfet with motor active braking designed for airsoft electric guns (AEG).
In semi fire mode piston isn't partially stretched, spring is fully released, parts in mechabox aren't under strain and nozzle locks hop-up chamber in greater part (depends on ROF).
Active break solves multiple shots in semi mode with weapons with a very high rate of fire (ROF).
Device increases gun rate of fire and battery holds longer, than with basic wiring.

SPECIFICATIONS:
- Very small device dimension, it fits nearly everywhere
- Pre soldered wires allow faster and easier installation into the gun, it is long enough for all kind of weapons. Simply cut wires to the required length and attach connectors (included in package)
-- There are high quality power wires 1,5 qmm (AWG16) with thin and hard MPPE insulation and signal blue wire 0.34 qmm (AWG22) with MPPE insulation
- Board covered by conformal coating, it protect device against water
- If you want to use your own wires, choose variant without wiring
- Designed for spring up to M160 (equivalent for current 75A single shot fire or 25A burst fire for max. 30s)
- Specified for common batteries up to 17V (Ni-xx 8.4 - 12V, lipol 7.4 - 14.8V)
- Active braking uses the excess energy from the motor to stop it. The braking effect is the most powerful with high torgue motor
- 6 wires connection
- Device size 27x10x7mm
- No current consumption in the idle mode
- No sparking on switch contacts
- In auto fire mode piston stops in random position due the mechabox design
- For right function is necessary to have a functional gearbox cut off lever, selector plate, reverse latch, trigger and trigger block, as it has the standard gearbox

DEVICE INSTRUCTIONS: you can download installation manual in English here [PDF, 596.09 kB]
PACKING:
- Device with wiring
- DeanT connector male
- 30A mini fuse
- 4x faston female 2,8mm
- 6x black heat shrink tube 3,2mm - length 20mm
- 3x black heat shrink tube 4,8mm - length 20mm
- Installation manual in English

WARNING: Installation of this device leave to expert, who could solder and disassemble airsoft gun. Never user soldering gun!

WIRING CONNECTION INTO THE GUN:

Modified connection diagram for weapon AUG or P90

Product description: Active brake II with wiring

Professionally made mosfet with motor active braking designed for airsoft electric guns (AEG).
In semi fire mode piston isn't partially stretched, spring is fully released, parts in mechabox aren't under strain and nozzle locks hop-up chamber in greater part (depends on ROF).
Active break solves multiple shots in semi mode with weapons with very high rate of fire (ROF).
Device increases gun rate of fire and battery holds longer, than with basic wiring.

SPECIFICATIONS:
- Presoldered wires allows faster and easier installation into the gun, it is long enough for all kind of weapons. Simply cut wires to the required length and attach connectors (included in package)
- On the devices are presoldered four high quality 1,5qmm (AWG16) power wires covered with MPPE insulation and two 0,34qmm (AWG22) signal wires
- Board covered by conformal coating, it protect device against water
- If you want to use your own wires, choose variant without wiring
- Designed for spring up to M210 (equivalent for current 150A single shot fire or 50A burst fire for max. 30s)
- Specified for common batteries up to 17V (Ni-xx 8.4 - 12V, lipol 7.4 - 14.8V)
- Active braking uses the excess energy from the motor to stop it. The braking effect is the most powerful with high torgue motor
- 6 wires connection
- Device size 35x12x7mm
- No current consumption in the idle mode
- No sparking on switch contacts
- In auto fire mode piston stops in random position due the mechabox design
- For right function is necessary to have a functional gearbox cut off lever, selector plate, reverse latch, trigger and trigger block, as it has the standard gearbox

DEVICE INSTRUCTIONS: you can download installation manual in English here [PDF, 663.23 kB]
PACKING:
- Device with wiring
- DeanT connector male
- 30A mini fuse
- 4x faston female 2,8mm
- 6x black heat shrink tube 3,2mm - length 20mm
- 3x black heat shrink tube 4,8mm - length 20mm
- Installation manual in English

WARNING: Installation of this device leave to expert, who could solder and disassemble airsoft gun. Never user soldering gun!

WIRING CONNECTION INTO THE GUN:

Modified connection diagram for weapon AUG or P90

Product description: Switch brake

Professionally made mosfet with active braking, which can be disabled by removing red jumper.
Device is designed to replace microswitch in the specific gearbox V2.
There is no modification needed.
In semi fire mode piston isn't partially stretched, spring is fully released, parts in mechabox aren't under strain and nozzle locks hop-up chamber in greater part (depends on ROF).
Active break solves multiple shots in semi mode with weapons with very high rate of fire (ROF).
Device increases gun rate of fire and battery holds longer, than with basic wiring.

SPECIFICATIONS:
- Easy installation inside the gearbox version 2, which replace microswitch
- Devices without wires, you can use max. 1,5qmm (AWG16) power wires and 0,5qmm (AWG20) signal wires
- Suitable for service center, if you are not familiar with soldering to the circuit board, choose device with wiring and accessories
- Disable active braking by unplugging red jumper, when you gun has Rate of fire under 20bb/s, otherwise it could lock up trigger on SEMI due too low gear speed.
- Motor will be under less stress without active braking.
- Designed for spring up to M160 (equivalent for current 75A single shot fire or 25A burst fire for max. 30s)
- Specified for common batteries up to 17V (Ni-xx 8.4 - 12V, lipol 7.4 - 14.8V)
- Active braking uses the excess energy from the motor to stop it. The braking effect is the most powerful with high torgue motor
- In auto fire mode piston stops in random position due the mechabox design
- For right function is necessary to have a functional gearbox cut off lever, selector plate, reverse latch, trigger and trigger block, as it has the standard gearbox

DEVICE INSTRUCTIONS: you can download an installation manual in English here [1.27 MB]
PACKING: device and installation manual in English

WARNING: Installation of this device leave to expert, who could solder and disassemble airsoft gun. Never user soldering gun!

WIRING CONNECTION INTO THE GUN:

Jefftron 80mm Round PVC Patch. PVC three colour patch with hook and loop backing - 80mm round

Jefftron PCB (Printed circuit board) Keychain
Features the Jefftron Leviathan Logo and is on a real PCB
Size: 28mm x 50mm